Wireless APP Camera Installation and Operating Instructions C935IP Version 1.0 PLEASE READ THESE INSTRUCTIONS CAREFUL
8 DOWNLOAD AND SETUP THE APP The Wireless APP camera is designed to deliver live video footage directly to your smart phone or tablet device. Please
9 1. Make sure the mobile device you are using is connected to the same Wi-Fi router the camera is connected to. 2. Locate the “OMGuard
10 In most cases, you can successfully add the camera according to the steps above. However, the camera will not find the network if Wi-Fi router tur
11 LIVE VIEW / SNAPSHOT / RECORDING Tap to take snapshot image(s) of the video. The captured snapshots will be stored in your mobile device.
12 VIEWING YOUR SNAPSHOTS For iOS You snapshots will be named with the time stamp and saved into the Camera Roll location of your mobile device. F
13 Tap EVENT LIST icon and the Date-Time filter would appear. User may define the period for system to display all available recorded file(
To Download/Delete the video file(s) in the EVENT LIST section, please follow the steps below: .DOWNLOAD Long press the vid
15 This function helps user to easily withdraw the recorded file(s) from the memory card. It is strongly suggested to download the file(s) at your h
16 MAIN PAGE OVERVIEW The MAIN PAGE section offers user an overview for all registered camera(s), including camera status (connected/d
17 4. Enter the default password 123456 in the Security Code column. 5. Click SAVE to complete the camera settings. The APP
The state of art WAPP camera is capable of deliver high quality Digital High Definition (HD) video to your smart-mobile device(s), which would require
18 In the CAMERA SETTING section you will allow to (1) configure system setting, (2) unregister camera from the APP and (3) enter event list for reco
19 SETUP PIN LOCK (iOS) (Android) If you enable PIN Lock, the user will be asked to enter the PIN code when you launch the APP. 1. Enable the
20 1. Launch Settings from your Home screen. 2. Tap Notifications. 3. Scroll down to find “OMGuard HD” APP and tap on it. 4. Switch the toggle to
21 ADVANCED SETTING This chapter explains the advanced settings for administrator. Administrator is the one who owns the administration password a
22 ADMIN PASSWORD The Admin Password is a specific security code for administrator to change the advanced settings. The default admi
23 TIME ZONE The drop-down list shows the world time zone. Select the time zone that will work the best for you. If your date/time is during t
24 Envi r onment Mode The Environment Mode settings allows you to select the power line frequency used at the location of WAPP camera. The
25 SENSITIVITY SETTING This defines the camera parameter for motion detection. Detection Mode PIR is hardware-based biomass detection. SOFTWARE us
26 Email to [email protected] Enter the email address for the recipient who receives the email alert. SD CARD SETTING Formatting your memory card
27 TROUBLE SHOOTING IF… SOLUTION The APP cannot found the camera • Make sure your network supports the DHCP protocol. • Make sure the ca
1 CONTENTS INTRODUCTION ... 2 WIRELESS DEVI
28 Low wireless signal Poor image quality • Wireless devices such as wireless home stereo system may reduce the signal strength. Leave as m
29 Bright white spots appear at night time • The camera's infrared LEDs produce invisible light that reflects off surfaces such as g
30 PRODUCTION SPECIFICATION Networking Parameter Wireless Technology IEEE 802.11 b/g/n Network Connection Ethernet (10/100 Base-T/Base -TX); Wi-
31 STORAGE MEDIA MANAGEMENT Micro SD Card Capacity (Class 10) HD / Better Image Better Streaming 4G 150 events 180 events 8G 300 events
2 INTRODUCTION PLEASE READ BEFORE YOU START Always use discretion when installing CCTV equipment, especially when there is perceived policy
3 FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) th
B Camera Stand x 1 D Power Adapter x 1 F Rj45 Connect Jack x 1 F Quick Start Guide x 1 KIT CONTENT AWireless App Camera x 1 C Ca
SAFETY AND INSTALLATION TIPS Do not attempt to open the units with the power adaptor plug connected to avoid any risk of personal injury. When ins
NIGHT VISION The camera has built-in infrared LEDs to allow you to view at night for 24-hour surveillance. The LEDs will automatically ac
CAMERA OVERVIEW Antenna Power Indicator Signal Indicator SD Card Slot PIR Infrared LEDs Stand RJ-45 Cable Powe
Commentaires sur ces manuels